Land Leveler
This page sets out the specification of the attachment in a form that can be matched to a carrier's data plate. Dimensions, hydraulic interfaces, wear parts and mounting geometry are treated as separate items rather than as one general description.
The grading frame, box grader, levelling rake data sheet gives rear as adjustable scarifier teeth; a buyer can confirm the same figure on the finished tool. The grading frame, box grader, levelling rake is specified with its centre of mass close to the plate, protecting stability on a short wheelbase carrier.
The grading frame, box grader, levelling rake is measured after painting, so the sheet describes the unit that actually reaches the site. The land leveler is supplied with leading edge recorded as reversible bolt-on blade rather than as a class average.
Every land leveler leaves the works with a measurement sheet, and the receiving workshop can repeat each entry with ordinary tools. The land leveler carries height control = skids or roller, and that pair is the reference used during commissioning.
The land leveler carries leading edge = reversible bolt-on blade, and that pair is the reference used during commissioning.
The land leveler is supplied with leading edge recorded as reversible bolt-on blade rather than as a class average. A tape check on the delivered grading frame, box grader, levelling rake should reproduce hydraulic circuit at none required, passive tool.
This land leveler is selected only after the carrier plate has been read, because auxiliary output decides how fast the working element can turn. Inspectors record hydraulic circuit as none required, passive tool once the grading frame, box grader, levelling rake has been assembled and painted.
Flow demand for rotating versions of the land leveler is read at full engine speed rather than from pump displacement. The grading frame, box grader, levelling rake carries its identification mark on the mounting frame, where it stays legible after repainting.
Rotating versions of the land leveler need a flow figure they can receive at full engine speed, not the theoretical pump displacement. mounting = universal quick-attach plate is the entry a workshop uses when it matches the land leveler to a host machine.
For procurement purposes rear is stated as adjustable scarifier teeth on the land leveler data sheet.
In the build record, frame for the land leveler is entered as open rectangular box-section lattice, and that entry is repeatable at goods-in. One line that decides the fit of this land leveler: mounting = universal quick-attach plate, measured after assembly.
Dimensional checks on the land leveler cover the envelope, the mounting face and the working width at ground level as three separate readings. Before fabrication, frame is fixed at open rectangular box-section lattice for the land leveler so the interface can be drawn.
On the land leveler, hydraulic circuit reads none required, passive tool, and the same value appears on the parts list. Bush and pin sizes for the grading frame, box grader, levelling rake appear on the spares page, so a local workshop can order without a sample.
Compatibility of this grading frame, box grader, levelling rake is established on paper before any hose is connected, from capacity, flow, geometry and spares. The leading edge figure of reversible bolt-on blade is written against this land leveler and repeated on the parts list.
For procurement purposes height control is stated as skids or roller on the land leveler data sheet.
In the build record, frame for the land leveler is entered as open rectangular box-section lattice, and that entry is repeatable at goods-in. The grading frame, box grader, levelling rake data sheet gives mounting as universal quick-attach plate; a buyer can confirm the same figure on the finished tool.
The grading frame, box grader, levelling rake is designed around a replaceable working edge, so the structure is inspected separately from the consumable components. If the carrier differs, the rear row for the land leveler is reissued; the standard entry here is adjustable scarifier teeth.
The land leveler is supplied with a measurement sheet, and each entry can be repeated at the receiving end with ordinary tools. If a variant is requested, the height control line for this grading frame, box grader, levelling rake is reissued; the standard value here is skids or roller.
Dimensions, circuit values and wear items are noted one by one for this grading frame, box grader, levelling rake so a later comparison isolates the item that changed. Inspectors record height control as skids or roller once the grading frame, box grader, levelling rake has been assembled and painted.
The land leveler carries hydraulic circuit = none required, passive tool, and that pair is the reference used during commissioning.
If a variant is requested, the rear line for this grading frame, box grader, levelling rake is reissued; the standard value here is adjustable scarifier teeth. In the build record, height control for the land leveler is entered as skids or roller, and that entry is repeatable at goods-in.
Mass on the grading frame, box grader, levelling rake is kept close to the plate, which holds the load centre inside the chart on a compact carrier. hydraulic circuit = none required, passive tool is the entry a workshop uses when it matches the land leveler to a host machine.
A tape check on the land leveler covers the envelope, the mounting face and the ground-level working width. Pin diameters and bush sizes for the land leveler are itemised one by one, which is what a local workshop needs to order replacements.
Hydraulic supply for the land leveler is read at rated engine speed, because a nominal pump figure says little about the flow at the coupler. mounting = universal quick-attach plate is the entry a workshop uses when it matches the land leveler to a host machine.
The mounting figure of universal quick-attach plate is written against this land leveler and repeated on the parts list.
The inspection record for the land leveler names the coupler type, the hose size and the number of independent hydraulic services. The grading frame, box grader, levelling rake is inspected for weld continuity along the load path before the working edge is fitted.
On the land leveler, relief pressure at the carrier has to sit above the working requirement and below the maximum rating of the tool. Before fabrication, frame is fixed at open rectangular box-section lattice for the land leveler so the interface can be drawn.
Specification items are itemised in the table in the order a workshop would check them. General compact loader ranges appear where useful, but the figures stamped on the carrier are the ones that govern. Those entries are taken from the Land Leveler on this page.
| Specification row | Works entry | Verification method |
|---|---|---|
| Frame | Open rectangular box-section lattice | Measured with a tape |
| Leading edge | Reversible bolt-on blade | Checked at goods-in |
| Rear | Adjustable scarifier teeth | Read from the carrier plate |
| Height control | Skids or roller | Checked at goods-in |
| Hydraulic circuit | None required, passive tool | Read from the carrier plate |
| Mounting | Universal quick-attach plate | Repeated at the first service |
If the carrier differs, the frame row for the land leveler is reissued; the standard entry here is open rectangular box-section lattice.
Start with rated operating capacity and the height control entry of skids or roller; both are recorded for this land leveler and both can be rechecked on arrival. The grading frame, box grader, levelling rake is drawn with the hose exit clear of the pivot arc, then that clearance is rechecked on the finished unit.
The interface sheet lists the coupler size, the number of services and hydraulic circuit as none required, passive tool for the grading frame, box grader, levelling rake, so the answer is written down before dispatch. Dimensions, circuit values and wear items are recorded one by one for this grading frame, box grader, levelling rake so a later comparison isolates the item that changed.
For this land leveler the receiving workshop measures mounting against the stated universal quick-attach plate with a tape or gauge; no special equipment is needed. The grading frame, box grader, levelling rake data sheet gives rear as adjustable scarifier teeth; a buyer can confirm the same figure on the finished tool.
Wear items are listed apart from the structure on the grading frame, box grader, levelling rake; frame is recorded as open rectangular box-section lattice so the correct replacement can be identified. The grading frame, box grader, levelling rake is specified with its centre of mass close to the plate, protecting stability on a short wheelbase carrier.
The figures here describe one build configuration. Any option that alters the interface is recorded as its own line rather than folded into a general statement.
E-mail: sales@mingycn.com | LINE: mingyicn
Tell the factory which carrier you run, its auxiliary output and the ground you work on. Mounting geometry, hydraulic requirement and the build photographs for that exact tool are confirmed in the reply, with technical questions answered directly.
