Ripper Scarifier
The following specification is written for readers who already have a machine and need to establish fit. It covers construction, interface, hydraulic supply, load position and the service items that follow from each choice.
One line that decides the fit of this ripper scarifier: hydraulic circuit = none required, passive tool, measured after assembly. Hose routing on the ripper attachment, scarifier rake, ground ripper is drawn clear of pivot points and inspected again after the first hours of operation.
Plate flatness and wedge engagement on the ripper scarifier are checked with a straightedge before the coupler is accepted. The ripper scarifier is weighed as built, and that mass is entered into the carrier chart before the load limit is set.
For this ripper attachment, scarifier rake, ground ripper the interface drawing shows the plate, the wedge pockets and the hose exit, and all three are read on the delivered unit. On the comparison sheet, mounting appears as universal quick-attach plate, which is the value measured after assembly of the ripper attachment, scarifier rake, ground ripper.
The ripper scarifier carries depth = set by carrier lift and shank position, and that pair is the reference used during commissioning.
In the build record, depth for the ripper scarifier is entered as set by carrier lift and shank position, and that entry is repeatable at goods-in. The ripper scarifier is checked for hose abrasion at every pivot after the first working shift.
The ripper scarifier drawing lists pin diameters and bush sizes, which is what a local workshop needs when ordering spares. On the comparison sheet, shanks appears as three to seven, clamped holders, which is the value measured after assembly of the ripper attachment, scarifier rake, ground ripper.
Spare parts for the ripper attachment, scarifier rake, ground ripper are identified by the entries on the sheet rather than by a photograph. If a variant is requested, the shanks line for this ripper attachment, scarifier rake, ground ripper is reissued; the standard value here is three to seven, clamped holders.
Before this ripper attachment, scarifier rake, ground ripper is accepted, flat-face couplers are identified by size and any case-drain requirement is verified in writing. teeth = replaceable hardened points is the entry a workshop uses when it matches the ripper scarifier to a host machine.
If the carrier differs, the hydraulic circuit row for the ripper scarifier is reissued; the standard entry here is none required, passive tool.
The ripper attachment, scarifier rake, ground ripper is specified with its centre of mass close to the plate, protecting stability on a short wheelbase carrier. Any option that changes the ripper scarifier interface is issued as a separate row on the same measurement sheet.
Compatibility of this ripper attachment, scarifier rake, ground ripper is established on paper before any hose is connected, from capacity, flow, geometry and spares. Read frame as rigid beam with wear protection on the ripper attachment, scarifier rake, ground ripper: it is a build dimension, not a class average.
On the ripper scarifier, teeth reads replaceable hardened points, and the same value appears on the parts list. The interface drawing for the ripper scarifier states frame as rigid beam with wear protection for the standard build.
The ripper scarifier drawing lists pin diameters and bush sizes, which is what a local workshop needs when ordering spares. For procurement purposes depth is stated as set by carrier lift and shank position on the ripper scarifier data sheet.
The ripper scarifier carries mounting = universal quick-attach plate, and that pair is the reference used during commissioning.
Where the host machine differs, the interface rows for the ripper attachment, scarifier rake, ground ripper are reissued before fabrication begins. Flow demand for rotating versions of the ripper scarifier is read at full engine speed rather than from pump displacement.
On the ripper scarifier, relief pressure at the carrier has to sit above the working requirement and below the maximum rating of the tool. A buyer comparing carriers will find hydraulic circuit entered as none required, passive tool for this ripper scarifier.
Relief pressure on the carrier has to sit above the working requirement of the ripper scarifier and below its maximum rating. The ripper scarifier is supplied with teeth recorded as replaceable hardened points rather than as a class average.
Steel grade and plate thickness for the ripper scarifier are entered on the build sheet, one by one from the wear items. Before fabrication, mounting is fixed at universal quick-attach plate for the ripper scarifier so the interface can be drawn.
The selection sheet for this ripper attachment, scarifier rake, ground ripper puts shanks at three to seven, clamped holders; that figure is rechecked on the finished unit.
Before dispatch the ripper attachment, scarifier rake, ground ripper is compared with its own mounting entry of universal quick-attach plate. The ripper attachment, scarifier rake, ground ripper is captured at goods-in against the same rows a buyer reads on this page.
Working width of the ripper scarifier is set against gate openings and transport limits before it is set against machine power. The shanks figure of three to seven, clamped holders is written against this ripper scarifier and repeated on the parts list.
A tape check on the delivered ripper attachment, scarifier rake, ground ripper should reproduce depth at set by carrier lift and shank position. The ripper attachment, scarifier rake, ground ripper data sheet gives frame as rigid beam with wear protection; a buyer can confirm the same figure on the finished tool.
The ripper attachment, scarifier rake, ground ripper is provided with its parts list, so each consumable can be named without referring back to a photograph. teeth = replaceable hardened points is the entry a workshop uses when it matches the ripper scarifier to a host machine.
Inspectors record teeth as replaceable hardened points once the ripper attachment, scarifier rake, ground ripper has been assembled and painted.
For the ripper attachment, scarifier rake, ground ripper, mounting is fixed at universal quick-attach plate before the mounting interface is drawn. The ripper attachment, scarifier rake, ground ripper is read after painting, so the sheet describes the unit that actually reaches the site.
The ripper scarifier is verified against the load chart with the arms raised, since reach reduces usable capacity more than mass alone. The frame figure of rigid beam with wear protection is written against this ripper scarifier and repeated on the parts list.
Each row in the table records one decision about the tool, from its structure through to its connection points. Range figures describe the compact loader class in general, so the data plate on the actual machine remains the controlling reference. Read each line as a property of this Ripper Scarifier.
| Data field | Recorded value | How the buyer checks it |
|---|---|---|
| Shanks | Three to seven, clamped holders | Recorded on the parts list |
| Teeth | Replaceable hardened points | Measured with a tape |
| Frame | Rigid beam with wear protection | Read from the carrier plate |
| Depth | Set by carrier lift and shank position | Compared with the load chart |
| Hydraulic circuit | None required, passive tool | Read from the carrier plate |
| Mounting | Universal quick-attach plate | Compared with the load chart |
For procurement purposes frame is stated as rigid beam with wear protection on the ripper scarifier data sheet.
The interface sheet lists the coupler size, the number of services and teeth as replaceable hardened points for the ripper attachment, scarifier rake, ground ripper, so the answer is written down before dispatch. A tape check on the delivered ripper attachment, scarifier rake, ground ripper should reproduce shanks at three to seven, clamped holders.
For this ripper scarifier the receiving workshop measures frame against the stated rigid beam with wear protection with a tape or gauge; no special equipment is needed. The workshop signs off hydraulic circuit = none required, passive tool for this ripper scarifier during the final inspection.
Wear items are listed apart from the structure on the ripper attachment, scarifier rake, ground ripper; depth is recorded as set by carrier lift and shank position so the correct replacement can be identified. One line that decides the fit of this ripper scarifier: hydraulic circuit = none required, passive tool, measured after assembly.
The ripper scarifier is supplied with hydraulic circuit = none required, passive tool on its measurement sheet, and that line is the one a buyer compares with the carrier chart. Hose routing on the ripper attachment, scarifier rake, ground ripper is drawn clear of pivot points and inspected again after the first hours of operation.
The specification above can be signed off against the delivered attachment item by item. Build photographs and the parts list accompany the machine, so the figures on this page are checkable rather than nominal.
E-mail: sales@mingycn.com | LINE: mingyicn
State the host machine, the auxiliary rating and the material, and the factory can reply in detail. The reply confirms the coupler geometry, circuit requirement and build photographs, and technical questions go straight to the workshop.
