Trencher Attachment
Selection begins with numbers that can be verified. The table below lists the build and interface items for this attachment, followed by the checks that decide whether it belongs on a particular machine.
The interface drawing for the trencher attachment states depth as set by boom length for the standard build. For the chain trencher, rotary trencher, cable plough, drive is fixed at hydraulic motor through gearbox before the mounting interface is drawn.
Before dispatch the chain trencher, rotary trencher, cable plough is compared with its own depth entry of set by boom length. The chain trencher, rotary trencher, cable plough is delivered with a parts list that names each consumable by dimension rather than by position.
Buyers fitting this chain trencher, rotary trencher, cable plough to an older machine should confirm wedge wear on the coupler before relying on the published interface. The spoil control figure of crumber and auger is written against this trencher attachment and repeated on the parts list.
The selection sheet for this chain trencher, rotary trencher, cable plough puts width at set by chain and tooth pattern; that figure is rechecked on the finished unit.
The trencher attachment is verified for hose abrasion at every pivot after the first working shift. The spoil control row for this trencher attachment is crumber and auger; it is a measured value, not an estimate.
Compatibility of this chain trencher, rotary trencher, cable plough is established on paper before any hose is connected, from capacity, flow, geometry and spares. Inspectors record mounting as universal quick-attach plate once the chain trencher, rotary trencher, cable plough has been assembled and painted.
The chain trencher, rotary trencher, cable plough is specified with its centre of mass close to the plate, protecting stability on a short wheelbase carrier. Before dispatch the chain trencher, rotary trencher, cable plough is compared with its own mounting entry of universal quick-attach plate.
Rotating versions of the trencher attachment need a flow figure they can receive at full engine speed, not the theoretical pump displacement. Inspectors record cutting member as toothed chain on boom once the chain trencher, rotary trencher, cable plough has been assembled and painted.
Inspectors record drive as hydraulic motor through gearbox once the chain trencher, rotary trencher, cable plough has been assembled and painted.
One line that decides the fit of this trencher attachment: mounting = universal quick-attach plate, measured after assembly. A second movement on this trencher attachment requires a second auxiliary service, which is noted on the interface sheet.
The chain trencher, rotary trencher, cable plough is signed off against a list that an operator can repeat at handover with a tape and a pressure gauge. Inspectors record depth as set by boom length once the chain trencher, rotary trencher, cable plough has been assembled and painted.
The chain trencher, rotary trencher, cable plough carries its identification mark on the mounting frame, where it stays legible after repainting. Read drive as hydraulic motor through gearbox on the chain trencher, rotary trencher, cable plough when the carrier chart is being checked.
The chain trencher, rotary trencher, cable plough is designed around a replaceable working edge, so the structure is inspected separately from the consumable components. width = set by chain and tooth pattern is the entry a workshop uses when it matches the trencher attachment to a host machine.
Read spoil control as crumber and auger on the chain trencher, rotary trencher, cable plough: it is a build dimension, not a class average.
Procurement uses the width figure of set by chain and tooth pattern to identify this chain trencher, rotary trencher, cable plough against other builds. One line that decides the fit of this trencher attachment: cutting member = toothed chain on boom, measured after assembly.
The chain trencher, rotary trencher, cable plough is signed off against a list that an operator can repeat at handover with a tape and a pressure gauge. The trencher attachment carries drive = hydraulic motor through gearbox, and that pair is the reference used during commissioning.
Relief settings for the trencher attachment are written against the carrier requirement, with the tool maximum shown beside them. In the build record, width for the trencher attachment is entered as set by chain and tooth pattern, and that entry is repeatable at goods-in.
Buyers fitting this chain trencher, rotary trencher, cable plough to an older machine should confirm wedge wear on the coupler before relying on the published interface. The trencher attachment carries spoil control = crumber and auger, and that pair is the reference used during commissioning.
Before fabrication, mounting is fixed at universal quick-attach plate for the trencher attachment so the interface can be drawn.
The cutting member row for this trencher attachment is toothed chain on boom; it is a measured value, not an estimate. Hose routing on the chain trencher, rotary trencher, cable plough is drawn clear of pivot points and inspected again after the first hours of operation.
Where the carrier differs from the class written down here, the interface rows for the chain trencher, rotary trencher, cable plough are reissued before fabrication. Read mounting as universal quick-attach plate on the chain trencher, rotary trencher, cable plough: it is a build dimension, not a class average.
If a variant is requested, the spoil control line for this chain trencher, rotary trencher, cable plough is reissued; the standard value here is crumber and auger. The trencher attachment is documented as one build configuration, and any option that changes the interface is issued as a separate row.
Every trencher attachment leaves the works with a measurement sheet, and the receiving workshop can repeat each entry with ordinary tools. The cutting member figure of toothed chain on boom is written against this trencher attachment and repeated on the parts list.
For procurement purposes cutting member is stated as toothed chain on boom on the trencher attachment data sheet.
Overall height of the trencher attachment is read with the tool parked level, not with the arms raised. Spare parts for the chain trencher, rotary trencher, cable plough are named by the entries on the sheet rather than by a photograph.
For procurement, the trencher attachment is documented by measurable fields rather than by a general description of what it can do. A buyer comparing carriers will find depth entered as set by boom length for this trencher attachment.
Each row in the table records one decision about the tool, from its structure through to its connection points. Range figures describe the compact loader class in general, so the data plate on the actual machine remains the controlling reference. All of the rows refer to the Trencher Attachment shown above.
| Parameter | Value on this build | Checked with |
|---|---|---|
| Cutting member | Toothed chain on boom | Read from the carrier plate |
| Depth | Set by boom length | Confirmed on the interface drawing |
| Width | Set by chain and tooth pattern | Repeated at the first service |
| Drive | Hydraulic motor through gearbox | Checked at goods-in |
| Spoil control | Crumber and auger | Compared with the load chart |
| Mounting | Universal quick-attach plate | Confirmed on the interface drawing |
depth = set by boom length is the entry a workshop uses when it matches the trencher attachment to a host machine.
Start with rated operating capacity and the width entry of set by chain and tooth pattern; both are recorded for this trencher attachment and both can be rechecked on arrival. Wear edges on the chain trencher, rotary trencher, cable plough are bolted rather than welded, which keeps replacement a workshop task.
The interface sheet lists the coupler size, the number of services and drive as hydraulic motor through gearbox for the chain trencher, rotary trencher, cable plough, so the answer is written down before dispatch. Dimensions, circuit values and wear items are recorded individually for this chain trencher, rotary trencher, cable plough so a later comparison isolates the item that changed.
For this trencher attachment the receiving workshop measures spoil control against the stated crumber and auger with a tape or gauge; no special equipment is needed. The interface drawing for the trencher attachment states depth as set by boom length for the standard build.
Wear items are listed apart from the structure on the chain trencher, rotary trencher, cable plough; mounting is recorded as universal quick-attach plate so the correct replacement can be identified. For the chain trencher, rotary trencher, cable plough, drive is fixed at hydraulic motor through gearbox before the mounting interface is drawn.
The figures here describe one build configuration. Any option that alters the interface is documented as its own line rather than folded into a general statement.
E-mail: sales@mingycn.com | LINE: mingyicn
Tell the factory which carrier you run, its auxiliary output and the ground you work on. The factory will confirm the mounting interface, circuit requirement and the build photographs for the exact tool, and will answer technical questions directly.
