Farm work asks a compact machine to do many jobs across the season. Ditching, land preparation and handling are all part of the same working week, and the carrier has to move between them without a workshop visit.
MINGYI mini crawler excavators suit that routine because they are built to order. A farm can specify the tracks, the engine and the attachments around the tasks that come round every year.
Seasonal tasks a farm excavator has to cover
Drainage and ditching come first, since wet ground has to be opened before it can be worked. A narrow bucket cuts the channel, and a grading bucket shapes the banks once the run is clear.
Land preparation follows, and a rotary tiller or a soil loosener can be run on the same carrier to break and mix ground. Handling jobs such as moving pallets or feed sit alongside these.
Track and attachment choices for farm ground
Rubber tracks let the machine cross yards and tracks without cutting into them, while steel tracks with rubber blocks give more grip on firmer field ground. The choice follows the route the machine uses most.
Attachments are matched to the carrier at ordering so the hydraulic circuit is right from the start. A quick coupler keeps a bucket, a grabber and a mower available on the one machine.
Track type, engine and attachment list are the choices a farm order turns on. Agreeing them at the outset is what lets one carrier cover a farm's work through the whole year.
Lifting and material handling with a mini excavator for agriculture Lifting with a machine built to dig needs a plan. The load, the radius and the ground under the class of machine all matter, and the safe figure is the one on the chart rather than the one that looks possible. Stability changes with reach. A load the excavator handles close in becomes a different proposition at full extension, so the working radius belongs in the plan before the lift rather than during it. Municipal and public works with mini excavator for agriculture Drainage repair, tree planting, footway reconstruction and cemetery work are all within the range of the unit in daily use. The jobs are small individually and continuous across the year. Noise and surface protection matter on public work. A machine of this size on rubber tracks across paving, with a sealed cab for the operator, suits the conditions better than a larger tracked machine. Working a mini excavator for agriculture in confined spaces Clearance above matters as much as around. Door heights, pipework and overhead services set the limit for the equipment on site indoors, and measuring them first avoids a machine that arrives and cannot be used. Ventilation is the other indoor constraint. Running the machine itself inside a closed structure needs air movement, and that is a planning item rather than something to discover after the first hour. Boom configuration for mini excavator for agriculture Extended and offset boom configurations change reach and working range. The model in question with a longer arm reaches further but lifts less at full extension, so the specification is set against the deepest and furthest point on the job list. Detachable boom sections are used where transport length matters. The machine in that duty that has to travel on a standard trailer can be built so the arm comes off for the road and goes back on at the site. Track choice for mini excavator for agriculture Rubber tracks suit paved and landscaped ground because they spread the machine weight and leave the surface intact. Steel tracks with rubber blocks are specified where the ground is rougher or the working day is longer, and the choice can be made per machine rather than accepted as a factory default. Undercarriage selection is a ground question, not a preference question. The unit on the job running on finished paving needs rubber; the same machine on demolition rubble or rock wears rubber quickly, so steel with rubber blocks becomes the better answer over a full season. OEM and fleet customisation of mini excavator for agriculture Distributors and rental fleets usually need the machine to look like theirs. Paint, decals, seat colour and attachment branding can be specified on a machine built for the work at build time rather than applied after import. Documentation can be prepared to suit the importer. Manuals, parts books and decal sets for the equipment in service can be supplied with the buyer's own branding where the order size justifies it. Getting the excavator through a narrow gap The first question on most job lists is whether the machine can reach the work at all. This class of machine is chosen against the narrowest point on the route - a garden gate, a doorway, a gap between two walls - because a machine that arrives and then cannot pass loses a day, not an hour. Contractors who buy the unit in daily use normally have one job in mind that nothing else reaches. The purchase order follows the access measurement, not the other way round, and the build sheet is then settled around it. Running a machine of this size in a rental fleet The specification that rents best is usually the simplest one to explain at the counter. The equipment on site with rubber tracks, a canopy and a coupler covers the majority of weekend and short-term hires. Fleet buyers also weigh transport. The machine itself that a customer can tow on a normal licence and a standard trailer is a hire that does not need a delivery truck, which changes how often it goes out. Working the model in question through the seasons Weather decides which days are productive. Rain turns some ground unusable and cold changes how the machine in that duty starts and warms up, so planning the wet months around maintenance is more useful than planning around output. Seasonal planning smooths the workload. Machines that are busy for a few months and idle for the rest benefit from a service slot in the quiet period, and the unit on the job prepared in the off-season starts the busy months reliably. Acceptance checks when a machine built for the work arrives Delivery day is the best time to find a problem. Checking the specification against the order, the fluid levels, the fasteners and any transport damage while the excavator is still on the trailer is faster than claiming later. A function check before the machine goes to work is worth the hour. Running through the controls, the travel and the attachment circuit on the equipment in service confirms it is set up as specified and ready for the site. Export packing and shipping of this class of machine Machines leave the factory prepared for container or flat rack shipment. The unit in daily use is normally shipped with the attachment set and the spare parts list agreed in advance so the container is planned once. Export documentation, decals and paint are settled before packing. Asking for them with the a machine of this size order avoids a second handling session and keeps the machine on the booked vessel. Daily checks and maintenance on the equipment on site Daily maintenance on the machine itself is a short list: engine oil level, coolant, track tension, hydraulic oil level and a look at the hoses. Ten minutes at the start of the shift prevents most of the failures that stop a machine. Track tension is the item most often neglected. The model in question run with slack tracks wears the undercarriage and can throw a track on a turn; run too tight, the same components wear from the other direction. Specification data for the machine in that duty Where the unit on the job is being specified for a job list, the table below gives the factory figures that matter most: what the machine weighs, how deep and how far it works, and what it measures on a trailer. Figures are factory figures and are confirmed on the build sheet for a machine built for the work. Where a job sits between two models, the larger machine usually takes less time than the smaller one spends on rework. Digging near water, gas and cable is a precision job. The equipment in service is used here because the operator can work in short controlled cuts and because the machine can be positioned without driving over the run being exposed. Utility crews specify the excavator with a narrow bucket and good visibility for exactly this reason: the machine has to stop at the service, not at the edge of the operator's view.
Reference specification — mini excavator range 09W 20-1W 30-2W 25L Operating weight 1100 kg (2425.08 lb) 1800 kg (3968.32 lb) 2700 kg (5952.48 lb) 2200 kg (4850.17 lb) Transport size (L×W×H) 1800 × 750 × 1970 mm 2550 × 1100 × 2200 mm 3000 × 1100 × 2700 mm 3000 × 1300 × 2700 mm Max digging depth 1250 mm (49.21 in) 1800 mm (70.87 in) 2200 mm (86.61 in) 2300 mm (90.55 in) Max digging height 2800 mm (110.24 in) 2820 mm (111.02 in) 3000 mm (118.11 in) 3100 mm (122.05 in) Max dumping height 1700 mm (66.93 in) 2050 mm (80.71 in) 2000 mm (78.74 in) 2050 mm (80.71 in) Max digging radius 2570 mm (101.18 in) 3050 mm (120.08 in) 3800 mm (149.61 in) 3900 mm (153.54 in) Max digging distance 1869 mm (73.58 in) 2300 mm (90.55 in) 3050 mm (120.08 in) 3100 mm (125.05 in) Minimum turning radius 1000 mm (39.37 in) 1450 mm (57.09 in) 1750 mm (68.9 in) 1800 mm (70.87 in) Travel speed 3 km/h (1.86 mph) 5 km/h (3.11 mph) 7 km/h (4.35 mph) 7 km/h (4.35 mph) Gradeability 30° 30° 30° 30° Fuel consumption 1-1.3 L/h (0.264—0.343 gal) 2-3 L/h (0.528—0.793 gal) 2-3 L/h (0.528—0.793 gal) 2-3 L/h (0.528—0.793 gal) Fuel tank capacity 8 L (2.11 gal) 16 L (4.23 gal) 16 L (4.23 gal) 16 L (4.23 gal) Hydraulic oil tank 16 L (4.23 gal) 18 L (4.76 gal) 20 L (5.28 gal) 18 L (4.76 gal) Dozer blade lift height 180 mm (7.09 in) 180 mm (7.09 in) 230 mm (9.06 in) 230 mm (9.06 in) Dozer blade drop depth 210 mm (8.27 in) 210 mm (8.27 in) 280 mm (11.02 in) 280 mm (11.02 in)
Q. Who chooses this class of machine?
A. Farm and orchard work is seasonal and varied - trenching at planting, drainage before the rains, clearing and grading after harvest - and one compact machine covers most of that calendar. Rubber tracks and a swing boom protect roots and irrigation lines while the carrier stays on the headland. MINGYI builds the 08, 12 and 18 models covering the 0.8 to 6 tonne class, and the unit in daily use is where that range meets agriculture.
Q. Which farm jobs come first?
A. Drainage before the rains, trenching for water and power at planting, then clearing, grading and post-hole work through the season. One compact excavator with a bucket, an auger and a rake covers most of that calendar.
Q. How do I get a specification?
A. Send the model, the destination and the attachment list by email or LINE - the channels listed just below this section. The reply covers the specification, lead time, packing and freight in one document, with the agriculture build sheet attached.
Planning the season around a machine of this size
Downtime is simplest when it is planned. Booking the service for the equipment on site in the quiet part of the season takes nothing from the schedule, while the same work in the busy weeks gives up a day of output every time.
Hot, humid and dusty conditions around the machine itself
Heat and dust shorten service intervals rather than machine life. In these conditions the filters on the model in question need attention more often, and the cooling surfaces need to be kept clear to hold the working temperature.
Fuel, oil and fluid quality for the machine in that duty
Fluid quality is a storage problem before it is a machine problem. Water and sediment in a drum will find the injection system of the unit on the job eventually, and a settling period is nothing compared with a pump.
E-mail ： sales@mingycn.com
LINE （ ID ）： mingyicn
Related pages
oem mini excavator manufacturing · china mini excavator supplier · Front Wheel Loader: Reading Boom, Hinge and Axle Specifications · Mini Excavators
